spotdetective.blogg.se - Firewall ports needed by ookla speedtest

FIREWALL PORTS NEEDED BY OOKLA SPEEDTEST SERIES

If you have daisy-chained switches, make sure the connection between the links is not saturated when you are doing testing.

If you find an issue, consult with a networking expert who can advise you on a fix. Meaning the ethernet up to the MoCA adapter and then again on the other side. If you have a MoCA network in your home, test on either side to eliminate the MoCA from the equation. We have seen people use ethernet over long coax cables (MoCA).

Your test device should start as close to the router as possible.

When possible, use a PC/MAC for the test with at least gigabit ethernet.

Wi-Fi tests may be comparable in slower networks, but for anything beyond 200 Mbit, you should use Ethernet first. This takes all of the variables that come with Wi-Fi out of the equation.

Test via an Ethernet connection to get a baseline.

Make sure any ethernet switch can handle wire-speed switching for all the ports. If your ethernet is going through a slow switch, everything downstream will be slowed as well.

Remember, the speed from one point to another point is only as good as the slowest point in the journey.

Below is an example for macOS where the speed can be set to automatic or to a fixed speed. A bad cable or connecting to a slow switch can cause a device to slow the connection automatically.

On other devices, check to see the device settings to make sure they are connecting at the speed you expect and that a slower speed wasn't manually or automatically set.

On Firewalla, tap on Settings > About > Port Speed to look at port speed to check the speed of devices connected directly to Firewalla.

Sometimes devices will negotiate at a lower speed.

If you have any doubt about a cable, test or replace it.

Make sure cables are in good condition.

Replace any CAT 5 cables if you find them. Gigabit networks require CAT 5E, 6, or 7 ethernet cables. By testing each separately you can quickly identify where any issues are.

Test From Firewalla to the Internet. In the Firewalla app we have an Internet test that measures only the connection from Firewalla to Internet speed servers (shown in white).Test Wi-Fi using either the Wi-Fi Speed Test in the Firewalla app (described below) or use on any device.For this, use the local network test described below by visiting with an ethernet connection. Test Ethernet connections starting those coming directly from your firewalla and then on any segment that does not seem to perform.

FIREWALL PORTS NEEDED BY OOKLA SPEEDTEST SERIES

Testing and tuning your network can be done in a series of steps: If this does not solve your problem, please get in touch with the support team here (If possible, please let us know some of your test results, it will make the diagnostic process faster) Especially if you have a Gigabit WAN network or faster, here are some tips to get the most meaningful results and to use Firewalla to optimize all your equipment. Nmap done: 1 IP address (1 host up) scanned in 1.Testing the speed of your network is both an art and a science. Other addresses for (not scanned): IPv4 address Traffic over port 8080 is blocked, generally by network appliance such as firewall connect to IPv6 address port 8080 failed: No route to hostįailed to connect to port 8080: No route to hostĬurl: (7) Failed to connect to port 8080 after xyz ms: Connection refused.Restart Speedtest Server if you have made changes to the OoklaServer.properties file as the configuration is only read at the process startĬurl: (6) Could not resolve host : Ī DNS AAAA record is not configured properly or does not exist.Ĭurl: (7) Failed to connect to port 8080.Try Nmap to find instances of ports 8080 or 5060 being closed.Verify that the AAAA record is configured properly.

Confirm that IPv6 traffic is not blocked on any intermediary network appliances that Speedtest traffic may route through.Outside of these basic requirements if issues persist with IPv6 for Speedtest Server additional troubleshooting considerations should be reviewed. IPv6 traffic must be able to flow over ports 80 for UDP and TCP."eIPv6 = true" configured in the OoklaServer.properties file.The following requirements must be met for Speedtest Server to work with IPv6 By default the Speedtest Server daemon is enabled to allow IPv6 but some instances have the feature disabled or otherwise commented out in the OoklaServer.properties file. IPv6 functionality is a required for a server to be displayed for public use on.